Skip to content
Looking for coffee carts & catering? Click here

Coffee guides · Milk

How do I steam milk at home?

Start with cold milk in a cold jug, let in a little air for the first few seconds, then sink the wand to spin the milk until the jug is too hot to hold, about 60–65 °C. Less air for a flat white, more for a cappuccino.

The short answer

Stretch first, then spin. Air goes in only while the milk is cool, and the rest of the time is spent swirling it into fine, glossy microfoam. Stop at 60–65 °C and pour straight away.

You’ll need

  • An espresso machine with a steam wand
  • A stainless steel milk jug with a pointed spout
  • Cold milk, straight from the fridge
  • A thermometer while you learn; your hand on the jug after that

Method

  1. Fill the jug to just below the base of the spout. Milk grows as it takes on air, and needs room to spin. Use a jug sized for the drink: a small jug for one, a larger one for two. Too little milk in a big jug is hard to control.
  2. Purge the wand. Open the steam for a second into a cloth or the drip tray to clear out water.
  3. Tip of the wand just under the surface, then open the steam fully. Hold the wand a little off-centre so the milk starts to turn.
  4. Stretch: let in air. Lower the jug slowly so the tip sits right at the surface. You should hear a quiet paper-tearing hiss, not loud spluttering. Do this only while the milk still feels cool to the hand: a few seconds for a flat white, longer for a cappuccino.
  5. Spin: sink the tip slightly. Raise the jug a little so the hiss stops and the milk whirls. This folds the bubbles into fine microfoam. Keep it spinning.
  6. Stop at 60–65 °C. That’s when the jug becomes too hot to hold for more than a second. Close the steam before lifting the wand out, then wipe and purge it.
  7. Tap and swirl, then pour straight away. Tap the jug on the bench to pop any big bubbles, swirl until the milk looks like glossy paint, and pour into fresh espresso. Milk left sitting separates into foam on top and thin milk below.

Flat white, latte or cappuccino?

DrinkAir inTextureIn the cup
Flat whiteLeast: a brief stretchThin, silky, barely any visible foamA thin layer of microfoam on top; the strongest coffee taste of the three
LatteA little moreSilky with a bit more bodyMore milk than a flat white, with a slightly deeper foam layer
CappuccinoMost: a longer stretchThick, airy, still fine-bubbledA deep, dome-like foam, often dusted with chocolate

Cup sizes and foam depths vary from café to café; the order is what’s consistent. The technique is the same for all three. Only the length of the stretch changes.

Why 60–65 °C

Milk tastes sweetest warm. Go much hotter and it starts to taste cooked and flat, the foam breaks down, and the drink is too hot to enjoy for the first few minutes. Our espresso guide uses the same range. If you like a hotter coffee, warm the cup instead of the milk.

Plant milk

  • Use barista versions. They’re made to stretch, hold foam and resist splitting. Regular oat, almond or soy often won’t foam well.
  • Don’t overheat. Stay at 60–65 °C or a touch under. Most plant milks taste worse and split more readily when they’re pushed hotter.
  • Stretch less, sooner. Many plant milks foam quickly. Let in air early and briefly, then spin.
  • Coffee matters too. Bright, acidic coffee can taste sour in plant milk and makes splitting more likely. Our blend’s caramel and milk-chocolate notes carry through oat, almond and soy. More in coffee with oat and plant milk.

Common faults

ProblemLikely causeFix
Big, soapy bubblesToo much air, or air let in too lateKeep the tip just under the surface; stretch only while the milk is cool
Loud screech, no foamWand tip too deepLower the jug until you hear a gentle hiss
Spluttering and sprayingTip too high, out of the milkRaise the jug a little
Hot milk, no foamNo stretch at all, or regular plant milkLet in air for the first few seconds; use a barista version
Foam sits on top, milk underneathMilk not spinning, or left standingHold the wand off-centre; swirl the jug and pour straight away
Tastes cooked or flatOverheatedStop when the jug is too hot to hold, 60–65 °C
Plant milk splits in the cupToo hot, acidic coffee, or not a barista versionBarista milk, gentler heat, a less acidic coffee

If the milk is right and the drink is still sharp or harsh, the espresso is the problem: see sour espresso or bitter espresso.

Questions

What temperature should milk be steamed to?

60–65 °C, about when the jug becomes too hot to hold. Hotter and it starts to taste cooked and the foam breaks down.

How do you get microfoam?

Let in air briefly at the start, with the wand tip just under the surface, then sink the tip slightly so the milk spins and folds the bubbles in. Tap and swirl the jug before pouring.

What is the difference between a flat white, latte and cappuccino?

Mostly the foam. A flat white has a thin layer of silky microfoam, a latte a little more, and a cappuccino a deep, airy foam. The milk is stretched for longer as you go from one to the next.

How do you steam oat milk?

Use a barista oat milk, let in air early and briefly, and stop at 60–65 °C or a touch under. Overheated oat milk tastes flat and its foam collapses.

Why won’t my milk froth?

The wand tip is too deep to draw in air, the milk is already warm when you start, or it’s a regular plant milk rather than a barista one. Start with cold milk and keep the tip right at the surface for the first few seconds.

A blend built for milk, any milk

Buy whole beans

The shot underneath

Espresso guide